SPECIAL SWITCH FOR MOLECULAR INDUCTANCE
General characteristics
The pattern ard-1 is a switch for inductive molecular detection that is activated by the approach and stays ignition while the person is inside the perceptive radius, the sensibility multiplies until for 5 times later on of the working when detecting the presence of a person, this allows 2 things one that is not activated with the step of a person without consent and the other one that when it is using doesn't light and turn off to come closer or to retire with any movement, these technical characteristics are useful in the practice, for example in the application of a watering-can without mechanical key, you will bring near the hand at a distance from 2 to 5 centimeters to the ceramic so that lights the water, or to adjust it to such a point that is necessary to play it, but when being taking a bath the water doesn't fade until the person doesn't retire of the area of the bathroom, and equally when she settles in a hands washer.
INSTALLATION
Generalities
The ARD-1 has the quality of converting the ceramic or the wood and even other different materials in an amplifier inductor, this is good to transform an entire bathroom piece of furniture into a switch or a wall like that of a watering-can in such a way that lights in passing automatically the key with to play it or to come closer to her in any point.
All these characteristics can be adjusted to more or smaller sensibility and it distances of reach according to it requires it that is to say needed by the installer, adjusting the screw of adjustment of the sensor, some how many thousandth more or less of adjustment they vary the sensibility and behavior of the working, for it uses it the screw of fine adjustment and the pads transductors to increase or to diminish the approach from the sensor to the material of the piece of furniture or wall where settles.
Has present that the adjustment is logarithmic inverse dual and if it moves away or Preposition the sensor to the contact surface can increase or to diminish its sensibility bringing near as moving away.
The location of the sensor as much as the variability of materials and disposition of steel constructions, as the distancing to pipes nails or metallic screws, density of the blocks or near friezes, types and qualities of ceramic etc. etc. are moderators that vary as much the behavior as the sensibility of the sensor.
¢can be located the components and sensors in 2 ways an embedding for the front hitting the ceramic that will cover it with some soft material of easy re mobility, like chew or other similar, to be able to consent to you adjust them and manual working when it is pertinent.
Or some type of hidden hinges so that it is not noticed that there is a door, (sees the drawing)
The other one is embedding from behind of the wall with some floodgate that covers it appropriately, and for which you can adjust and to consent to the manual working.
(See the illustration for further clarity)
For it will adjust it in each installation to different sensibilities according to they require it the variables of the environment of the materials.
Sensor ARD-1
Places and more appropriate points or recommended to install the sensors.
SENSIBILITY OF TURNING OFF
|
SENSIBILITY OF TURNING OFF
|
STEPS TO INSTALL
" This sensor is designed to always be placed behind the ceramic so that it is hidden, either inside of and behind the ceramic of the wall or under from behind of the ceramic furniture of the bathroom like they are it handswasher or in the kitchen dishwasher, if these furniture are made of stainless steel it will prove very well how it works or to look for the most appropriate place in which can work correctly.
“it can embed and to place hidden mentions as much the sensor circuit as the electromechanical control which possesses 2 keys, one it is to limit the flow of exit of the water so that it is the most appropriate to the purpose, and be this way preset, the alone other key was used in the event of emergency, to open the step of the water in case the electric light is fenced.
“This sensor can work superficially but its behavior is very different and its action is very short since there is not amplification for the out one,
This is due to that is designed to use the ceramic as transducer amplifier, to use it this way he will have to change to the 3º exit of the relé which doesn't bring terminal connection.
" first it locates all the components as plans to install them in the place, place the sensor with adhesive tapes and make the adjustments previously, for former to make sure that worked well, if all this correct one then proceeds to the definitive installation hitting the sensor and installing the rest.
1º. hit the sensor container with silicon for glass or silicon for temperature depending i wants it completely fixed it uses the first one, if you plans to change it it uses the second.
2º. adjust this way so that you prove the sensibility, if it is not adapted to the necessity it can use the pads transductors inserting them in the groove below the sensor, then adjustment smoothly until achieving their wanted objective.
3º. This team is designed to be used by many years without problems and this highly protected against all electric, alone type of incidents will be able to be damaged by accidents ends that generate high accidental voltages.
4º. has 10 year-old guarantee against factory defect.
5º. Technical service in the event of damage leaves of the client calls
in U:S:A: 800-3779943171 for Venezuela 0416-5720719.
